GENERAL SPECIFICATIONS
|
| Model Designation:
Windsor 6: C51 |
| Wheel base: 125-1/2 |
| Valve Location: In
block |
| Bore and
Stroke: 3-7/16
x 4-3/4 |
| Piston displacement, Cubic
Inches: 264.5 |
| Compression
ratio: 7.00 |
| Maximum
Brake Horsepower: 119
@ 3600 RPM |
| Maximum
Torque Lbs.Ft. @ RPM: 218
@ 1600 RPM |
| Normal
Oil Pressure Pounds: 50 |
TUNE UP SPECIFICATIONS (all models) |
| Spark Plug
Make: Auto-Lite AR-8 |
| Spark Plug
Gap, Inch: .035 |
| Firing
Order: 153624 |
| Timing
Mark: 0; location: Vib. Damper |
| Engine
Idle Speed, RPM: 475 |
| Cylinder
Head Torque Lbs.Ft.: 70 |
| Compression
Pressure & Cranking Speed: 120 min. |
| Voltage & Polarity: 6
volts, positive ground |
PISTON AND RING SPECIFICATIONS
|
| Fitting
Pistons with Scale: Pistons
removed from above. Shim thickness: .001 |
| Pounds
on a Pull Scale: 5 to 7 |
Ring End
Gap: In tapered bores,
fit rings in tightest portion of ring travel
Compression: .015
Oil: .015 |
| Clearance in Groove: Compression:
.Top ring: .0025-.004, second ring: .002-.0035; Oil: .001-.0025 |
| Wristpin
Diameter, Inch: .8591-.8593 |
VALVE SPECIFICATIONS
|
Operating
Clearance:
Intake:
.008 Hot; Exhaust: .010 Hot |
| Valve Seat
Angle, degrees: 45 |
| Clearance for Timing Intake: .014 |
Valve Timing: (BTDC
= before top dead center; ATDC = after top dead
center)
Intake
opens: 12 BTDC
Exhaust
Closes: 6 ATDC |
Valve Spring
Pressure Pounds at Inches Length:
Inner
Spring: 40 @ 1-3/4 |
| Valve Stem
Clearance: Intake: .001-.003; Exhaust:
.002-.004 |
ENGINE BEARING SPECIFICATIONS
|
Connecting Rod Bearings:
Journal
Diameter, Inches: 2.124-2.125
Bearing Clearance, Inch: .0005-.0015
Rod End Play, Inch: .006-.011
Rod Bolt Tension: Lbs.Ft.: 45-50 |
Main Bearings:
Journal
Diameter, Inches: 2.499-2.500
Bearing clearance: .0005-.0015
Shaft End Play: .003-.007 (Thrust
on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 80-85 |
CAPACITY DATA
|
Cooling
System:
Without
heater: 15 quarts; With heater: 16 quarts |
| Fuel Tank: 17 gallons |
| Engine
Oil: 5 quarts (w/torque converter, engine & converter combined require 12 quarts, 13 when filter is changed) |
| Transmission: Manual: 2-3/4 Pints; for semi-automatic trans: 3 pints |
| Rear Axle: 3-1/4
pints |
AUTO-LITE DISTRIBUTOR SPECIFICATIONS
|
| Distributor part number: 1AT-4012
(distributor rotates clockwise) |
| Cam Angle,
degrees: 39 |
| Breaker Point opening, Inch: .020 |
| Condenser
Capacity: .25-.28
Mfds. |
| Breaker Arm Spring Tension: 17-20
Oz. |
Centrifugal Advance: (degrees
at RPM of distributor)
Advance starts: 1 @ 450 RPM
Full Advance: 10 @ 1425 RPM
Vacuum Advance (degrees @ Inches of Mercury)
Advance Starts: 1 @ 6
Full Advance: 9 @ 15 |
AUTO-LITE GENERATOR SPECIFICATIONS
|
| Generator
Number: GGW-6001J; GGU-6001G; GGU-6001T, GGU-6001R, GGJ-6003A, GGJ-6004A
(generator rotates clockwise, 6 volts, Positive
Ground) |
| Generator
output: GDW-6001J: 45 35 amps @ 2125 RPM; GGU-6001G, GGU-6001T, GGU-6001R: 50 amps @ 1750 RPM; GGJ-6003A, GGJ-6004A: 55 amps @ 1700 RPM |
| Brush Spring
Tension: GGW-6001J, GGU-6001G, GGU-6001T, GGU-6001R: 35-53 oz.; GGJ-6003A, GGJ-6004A: 34-41 |
| Field Current at 5 Volts: GGW-6001J: 1.4-1.5; all others: 1.4-1.6 |
AUTO-LITE REGULATOR SPECIFICATIONS
|
| Regulator
Number: VBE-6001A, VAV-6001B, VBF-6001A |
Cutout
Relay:
Voltage
to close points: 6.5
Reverse current to open points: 4-6
Armature Air Gap: VBE-6001A, VBF-6001A: .031 inches; all others: .034 |
| Voltage
Regulator Setting: 7.3
volts |
| Current and Voltage Armature Air Gap: .048 inches |
| Current
Regulator Setting: VBE-6001A: 45 amps; VAV-6001B: 50 amps; VBF-6001A: 55 amps |
AUTO-LITE STARTING MOTOR SPECIFICATIONS
|
| Part number: MCL-6109 (rotates clockwise) |
| Bush Spring
Tension, Ounces: 42-53 |
| No Load
Test: 65
amps, 5 volts @ 4900 RPM |
| Torque
Test: 410 Amps, 2.0
volts; Torque: 8.0 ft/lbs. |
WHEEL ALIGNMENT SPECIFICATIONS
|
Caster,
Degrees
Limits: -1
to -2
Desired: -1-1/2 |
Camber,
Degrees
Limits: -3/8 to +3/8
Desired: 0 |
| Toe-In,
Inches: 0 to 1/16 |
Toe-Out
on Turns, Degrees: (If
toe-out is incorrect, when other adjustments are
correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 20-1/2 to 22-1/2 |
Kingpin
Angle, or Steering Axis Degrees: (If
king pin or spindle support angle are incorrect,
but camber is correct, look for bent suspension
arms or steering knuckle support)
5 to 6-1/2 |
