GENERAL SPECIFICATIONS
|
| Model Designation:
Series 60, Series 62, Series 75 |
| Wheel base: Series 60: 133; Series 62: 129; Series 75: 149-3/4 |
| Valve Location: In
head |
| Bore and
Stroke: 4
x 3-5/8 |
| Piston displacement, Cubic
Inches: 365 |
| Compression
ratio: 9.75 |
| Maximum
Brake Horsepower: 285
@ 4600 RPM |
| Maximum
Torque Lbs.Ft. @ RPM: 400
@ 2800 RPM |
| Normal
Oil Pressure Pounds: 30-35 |
TUNE UP SPECIFICATIONS (all models) |
| Spark Plug
Make: AC 44 |
| Spark Plug
Gap, Inch: .035 |
| Firing
Order: 18436572 (front
to rear: Right bank 2-4-6-8, left bank 1-3-5-7)
|
| Timing
Mark: "A" mark for premiurm fuel; "C" mark for regular fuel; location: Vib. Damper |
| Engine
Idle Speed, RPM: w/automatic 400 (in drive) |
| Cylinder
Head Torque Lbs.Ft.: 65-70 |
| Compression
Pressure & Cranking Speed: 165 min. |
| Voltage & Polarity: 12
volts, negative ground |
PISTON AND RING SPECIFICATIONS
|
| Fitting
Pistons with Scale: Pistons
removed from above. Shim thickness: .002 |
| Pounds
on a Pull Scale: 11 |
Ring End
Gap: In tapered bores,
fit rings in tightest portion of ring travel
Compression: .013
Oil: .013 |
| Clearance in Groove: Compression:
.0017-0035; Oil: .0008-.0026 |
| Wristpin
Diameter, Inch: 1.000 |
VALVE SPECIFICATIONS
|
Operating
Clearance:
Intake:
0 Exhaust: 0 |
| Valve Seat
Angle, degrees: 44 |
Valve Timing: (BTDC
= before top dead center; ATDC = after top dead
center)
Intake
opens: 22 BTDC
Exhaust
Closes: 27 ATDC |
Valve Spring
Pressure Pounds at Inches Length:
Inner
Spring: 65 @ 1.980 |
| Valve Stem
Clearance: Intake: .0001-.0025; Exhaust:
.001-.0025 |
ENGINE BEARING SPECIFICATIONS
|
Connecting Rod Bearings:
Journal
Diameter, Inches: 2.2488-2.2493
Bearing Clearance, Inch: .0005-.002
Rod End Play, Inch: .008-.014
Rod Bolt Tension: Lbs.Ft.: 40-45 |
Main Bearings:
Journal
Diameter, Inches: 2.625
Bearing clearance: .0008-.0025
Shaft End Play: .001-.005 (Thrust
on Rear Bearing)
Main Bolt Tension: Lbs.Ft.: 90-100 |
CAPACITY DATA
|
Cooling
System:
Without
heater: Series 60, 62: 17-1/4 quarts; With heater: 19-1/4 quarts
Without heater: Series 75: 17-1/4 quarts; With heater: 21-3/4 quarts
|
| Fuel Tank: 20 gallons |
| Engine
Oil: 5 quarts |
| Transmission: Automatic: 12 quarts |
| Rear Axle: 5
pints |
1956 Cadillac 365 V8 (285 hp) Engine Specs
1956 Cadillac 365 V8 (305 hp) Engine Specs
1956 Cadillac 365 (285 hp) V8:
Distributor Specs
1956 Cadillac 365 (285 hp) V8:
Generator Specs
1956 Cadillac 365 (285 hp) V8:
Regulator Specs
1956 Cadillac 365 (285 hp) V8:
Starting Motor Specs
1956 Cadillac 365 (285 hp) V8:
Engine Tightening Specs
1956 Cadillac:
Wheel Alignment Specs
Return to Cadillac Engine Specs Index
|
