GENERAL SPECIFICATIONS
|
| Model Designation: Champion
6: 14G |
| Wheel base:
2 & 4 door sedans: 116-1/2"; coupes & hardtop convertibles:
120-1/2"; Land Cruiser: 120-1/2" |
| Valve Location: In
block |
| Bore and
Stroke: 3
x 4 |
| Piston displacement, Cubic
Inches: 169.6 |
| Compression
ratio: w/synchromest
trans: 7.0; w/automatic: 7.5 |
| Maximum
Brake Horsepower: 85
@ 4000 RPM |
| Maximum
Torque Lbs.Ft. @ RPM: 138
@ 2400 RPM |
| Normal
Oil Pressure Pounds: 40 |
TUNE UP SPECIFICATIONS
|
| Spark Plug
Make: Champion J7 |
| Spark Plug
Gap, Inch: .025 |
| Firing
Order: 153624
|
| Ignition
Timing: IGN on Vib.
Damp. |
| Engine
Idle Speed, RPM: 550 |
| Cylinder
Head Torque Lbs.Ft.: 48 |
| Compression
Pressure & Cranking Speed: 120
Min. |
| Voltage & Polarity: 6
volts, positive ground |
PISTON AND RING SPECIFICATIONS
|
Fitting
Pistons with Scale:
Shim Thickness to use: .002
(1 inch wide feeler); |
| Pounds
Pull on Scale:: 11
to 16 |
Ring End
Gap: (Fit rings in tapered
bores for clearance shown in tightest portion of
ring travel.)
Compression: .007
Oil: .007 |
| Clearance
in Groove: Compression:
.002-.0025; Oil: .0015-.002 |
| Wristpin
Diameter, Inch: .7491-.7495 |
VALVE SPECIFICATIONS
|
Operating
Clearance:
Intake:
.016 Cold Exhaust: .016 Cold |
| Valve Seat
Angle, degrees: 45 |
Valve Timing: (BTDC
= before top dead center; ATDC = after top dead
center)
Intake
opens: 15 degrees BTDC
Exhaust
Closes: 10 ATDC |
Valve Spring
Pressure Pounds at Inches Length:
Inner
Spring: 54 @ 1-21/32 |
| Valve Stem
Clearance: Intake: .0015-.0035; Exhaust:
.0015-.0035 |
| Clearance
for Timing Intake: .020 |
ENGINE BEARING SPECIFICATIONS
|
Connecting Rod Bearings:
Journal
Diameter, Inches: 1.81175-1.81275
Bearing Clearance, Inch: .0005-.00215
Rod End Play, Inch: .005-.009
Rod Bolt Tension: Lbs.Ft.: 28-32 |
Main Bearings:
Journal
Diameter, Inches: 2.4370-2.4375
Bearing clearance: .0005-.0025
Shaft End Play: .003-.006 (Thrust
on front bearing)
Main Bolt Tension: Lbs.Ft.: 88-93 |
CAPACITY DATA
|
Cooling
System:
Without
heater: 10 quarts
With heater: 11-1/2 quarts |
| Fuel Tank: 18
gallons |
| Engine
Oil: 5 quarts |
| Transmission: w/out
overdrive: 1-1/2 pint; with overdrive: 2-3/4; w/auto.
trans: 9-1/2 quarts |
| Rear Axle: 2-1/2
pints |
AUTO-LITE
DISTRIBUTOR SPECIFICATIONS
|
| Distributor part number:
1AT-4010 (distributor rotates counter-clockwise
when viewed from top) |
| Cam Angle,
degrees: 39 |
| Breaker Point opening, Inch: .020
(plus or minus .002) |
| Condenser
Capacity: .20-.25 Mfds. |
| Breaker Arm Spring Tension: 17-20
Oz. |
Centrifugal
Advance: (degrees at
RPM of distributor)
Advance starts:
1 degrees @ 550
Full Advance:
7 @ 1400
|
Vacuum
Advance Data (degrees @ In. of Mercury):
Advance
starts:
1 @ 4-7/8
Full Advance:
9 @ 12 |
AUTO_LITE
GENERATOR SPECIFICATIONS
|
| Generator
Number: GGW-4801C
(generator rotates clockwise, 6 volts, positive
ground) |
| Generator
output: 45 amps @
2125 RPM |
| Brush Spring
Tension: 35-53 oz. |
| Field Current: 1.4
- 1.5 at 5 volts |
AUTO-LITE
REGULATOR SPECIFICATIONS
|
| Regulator
Number: VBE-6101A |
Cutout
Relay:
Voltage
to close points: 6.5
Reverse Current to Open Points: 4-6
amps
Armature Air Gap: .031 |
| Voltage
Regulator Setting: 7.3
volts |
| Current
Regulator Setting: 45
amps |
| Current
and voltage armature air gap, Inch: .048 |
AUTO-LITE
STARTING MOTOR SPECIFICATIONS
|
| Part number:
MZ-4157 (starter rotates clockwise) |
| Bush Spring
Tension, Ounces: 42-53 |
| No Load
Test: 68
amps, 5.0 volts @ 4000 RPM |
| Torque
Test: 280 Amps, 2.0
volts, Torque, Lbs.Ft.: 4.4 |
WHEEL ALIGNMENT SPECIFICATIONS
|
Caster,
Degrees
Limits: -1
to +2-1/2
Desired: -1-3/4 |
Camber,
Degrees
Limits: 0
to +1
Desired: +1/2 |
| Toe-In,
Inches: 1/16 to 1/8 |
Toe-Out
on Turns, Degrees: (If
toe-out is incorrect, when other adjustments are
correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 22-1/2
to 23-1/2 |
Kingpin
Angle, or Steering Axis Degrees: (If
king pin or spindle support angle are incorrect,
but camber is correct, look for bent suspension
arms or steering knuckle support)
5-1/4 |
