GENERAL SPECIFICATIONS
|
| Model Designation: V8
- U6 |
| Wheel base: 115-1/2 |
| Valve Location: In
head |
| Bore and
Stroke: 3.62" x
3.30" |
| Piston displacement, Cubic
Inches: 272 |
Compression
ratio:
Mainline w/standard & overdrive:
8.0;
Mainline w/Fordomatic: 8.4;
Customline w/standard & overdrive:
8.0;
Customline w/Fordomatic: 8.4 |
Maximum
Brake Horsepower:
Mainline w/standard & overdrive:
173 @ 4400 RPM
Mainline w/Fordomatic: 176 @ 4400
Customline w/standard & overdrive:
173 @ 4400 RPM
Customline w/Fordomatic 176 @ 4400 RPM |
Maximum
Torque Lbs.Ft. @ RPM:
Mainline w/standard & overdrive:
260 @ 2400
Mainline w/Fordomatic: 264 @ 2400
Customline w/standard & overdrive:
260 @ 2400
Customline w/Fordomatic: 264 @ 2400 |
| Normal
Oil Pressure Pounds: 50 |
TUNE UP SPECIFICATIONS
|
| Spark Plug
Make: Champion 870 |
| Spark Plug
Gap, Inch: .035 |
| Firing
Order: 15486372 (from
front to rear: Right 1-2-3-4; left 5-6-7-8
|
| Ignition
Timing: Marks on Vib.
Damp. Wide mark is TDC, each succeeding mark represents
2, 4, 6, 8 and 10 degrees before TDC. Set timing
3 degrees BTDC on cars with manual shift transmission
and 6 degrees BTDC on Fordomatic equipped cars. |
| Engine
Idle Speed, RPM: Manual
shift trans. 475; automatic shift trans. 450 |
| Cylinder
Head Torque Lbs.Ft.: 60-75 |
| Compression
Pressure & Cranking Speed: 160
Min. |
PISTON AND RING SPECIFICATIONS
|
Fitting
Pistons with Scale:
Removed
from Above
Shim thickness to use: .002
Pounds Pull on Scale: 5 to 10 |
Rings: (for
tapered bores for minimum clearance fit rings in
tightest portion of ring travel)
Ring Gap, Minimum: Compression: .010
Ring Gap, Minimum: Oil: .015
Clearance in Groove: Compression: .006
Max.
Clearance in Groove: Oil: .006 Max. |
| Wristpin
Diameter, Inch: .9120-.9123 |
VALVE SPECIFICATIONS
|
Operating
Clearance:
Intake:
.019 Hot
Exhaust: .019 Hot |
| Clearance
for Timing Intake: .019 |
| Valve Seat
Angle, degrees: 45 |
Valve Timing: (BTDC
= before top dead center; ATDC = after top dead
center)
Intake opens: 12 degrees BTDC
Exhaust Closes: 8 degrees ATDC |
Valve Spring
Pressure Pounds at Inches Length:
Spring:
64 @ 1.78 (only one spring used) |
Valve Stem
Clearance:
Intake:
.004
Exhaust: .005 |
ENGINE BEARING SPECIFICATIONS
|
Connecting Rod Bearings:
Journal
Diameter, Inches: 2.1880-2.1888
Bearing Clearance,
Inch: .0037 Max.
Rod End Play,
Inch: .012 Max.
Rod Bolt Tension,
Lbs.Ft.: 45-50 |
Main Bearings:
Journal
Diameter, Inches: 2.4980-2.4988
Bearing Clearance,
Inch: .0042 Max.
Crankshaft End
Play, Inch (taken on No. 3 bearing): .010 Max.
Main Bolt Tension,
Lbs.Ft.: 95-105 |
CAPACITY DATA
|
Cooling
System:
Without
heater: 19 quarts
With heater: 20 quarts
|
| Fuel Tank: 17
gallons (station wagons and couriers 19 gallons) |
| Engine
Oil: 5 quarts |
Transmission:
without overdrive: 3 pints
with overdrive: 3, station wagon 4-1/2
Automatic Transmission: 9-3/4 quarts |
| Rear Axle: 4
pints; Station wagon: 3 |
STARTING MOTOR SPECIFICATIONS
|
| Unit Number: FAR-11001A |
| Brush Spring Tension: 48-56
ounces |
| No Load
Test: 120 Amps, 12 Volts
@ 4800 RPM |
| Torque Test: 550
Amps, 5.0 Volts, 15.5 Lbs.Ft. Torque |
LOADAMATIC DISTRIBUTOR SPECIFICATIONS
|
| Cam Angle,
degrees: 28 |
| Breaker Gap, Inch: .014-.016 |
| Condenser
Capacity: .21-.25 Mfds. |
| Breaker Arm Spring Tension: 17-20
Oz. |
Distributor
Vacuum Advance Data:
Centrifugal Advance:
2 bbl carb.:
Degrees advance
at 300 RPM: 0 - 1/2, Inches vacuum: .15
Degrees advance
at 400 RPM: 1/4 - 1-1/4, Inches vacuum: .28
Degrees advance
at 800 RPM: 6-1/2 - 7-1/2, Inches vacuum: .96
Degrees advance
at 1200 RPM: 11-1/2 - 12-3/4, Inches vacuum: 2.21
Degrees advance
at 1600 RPM: 14-1/2 - 15-1/2, Inches vacuum: 3.41
Degrees advance
at 2000 RPM: 16 - 17-1/4, Inches vacuum: 4.6
4 bbl carb.:
Degrees advance
at 300 RPM: 0 - 1/2, Inches vacuum: .16
Degrees advance
at 400 RPM: 0-1, Inches vacuum: .29
Degrees advance
at 800 RPM: 5-1/2 - 6-1/2, Inches vacuum: .88
Degrees advance
at 1200 RPM: 8-1/2 - 9-1/2, Inches vacuum: 1.27
Degrees advance
at 1600 RPM: 11 - 12, Inches vacuum: 1.73
Degrees advance
at 2000 RPM: 13 - 14-1/2, Inches vacuum: 2.19
|
GENERATOR SPECIFICATIONS
|
| Generator
Number: FAR-10000B,
FAS-10000C (generator rotates clockwise) |
Generator
output:
30 Amps @ 3000 |
| Brush Spring
Tension: 30 oz. |
REGULATOR SPECIFICATIONS
|
| Regulator
Number: FAP-10505 |
Cutout
Relay:
Voltage
to close points: 12.4
Reverse Current to Open Points: 2-6 amps
Voltage regulator setting: 15.0 volts
Current regulator settins: 30 amps |
ENGINE TIGHTENING SPECIFICATIONS
(FT. LBS.)
|
| Spark Plugs: 15-20 |
| Cylinder
Head Bolts: 65-70 |
| Intake
Manifold: 23-28 |
| Exhaust
Manifold: 23-28 |
| Rocker
Arm Shaft Bracket: 12-15 |
| Rocker
Arm Cover: 2 - 2-1/2 |
| Connecting
Rod Cap Bolts: 45-50 |
| Main Bearing
Cap Bolts: 95-105 |
| Flywheel
to Crankshaft: 75-85 |
| Vibration
Damper or Pulley: 85-95 |
REAR AXLE AND BRAKE CYLINDER
SPECIFICATIONS
|
Ring Gear & Pinion
Backlash, Inch:
Passenger Car: .003-.008
Station Wagon: .003-.008 |
Drive
Pinion Adjustment:
Passenger Car: Shims
Station Wagon: Shims |
Drive Pinion
Bearing Adjustment:
Passenger Car: Spacer
Station Wagon: Spacer
|
Axle Shaft
End Play, Inch:
Passenger Car: None
Station Wagon: None |
Hydraulic
Cylinder Bore Sizes, Inch:
Wheel Cylinder:
Front: 1-1/8
Rear: 7/8 (station
wagon: 15/16)
Master Cylinder: 1 |
WHEEL ALIGNMENT SPECIFICATIONS
|
Caster,
Degrees
Limits: +1/2
to + 1-1/2
Desired: +1 |
Camber,
Degrees
Limits: +1/4
to +1-1/4
Desired: +3/4 |
| Toe-In,
Inches: 1/16 to 1/8 |
Toe-Out
on Turns, Degrees: (If
toe-out is incorrect, when other adjustments are
correct, look for bent steering arms.)
Outer wheel: 20
Inner Wheel: 24-1/2 |
Kingpin
Angle, or Steering Axis Degrees: (If
king pin or spindle support angle are incorrect,
but camber is correct, look for bent suspension
arms or spindle support)
7° 7' |
