GENERAL SPECIFICATIONS
|
| Model Designation: Super
V8 - Series 50 with Dynaflow |
| Wheel base: Super
V8: 127 |
| Valve Location: In
head |
| Bore and
Stroke: 4
x 3.2 |
| Piston displacement, Cubic
Inches: 322 |
| Compression
ratio: Super V8 with Dynaflow: 8.5 |
| Maximum
Brake Horsepower:
Super V8 with Dynaflow: 182 @ 4100 RPM |
| Maximum
Torque Lbs.Ft. @ RPM:
Super V8 with Dynaflow: 300 @ 2000 RPM |
| Normal
Oil Pressure Pounds: 35 |
TUNE UP SPECIFICATIONS
|
| Spark Plug
Make: AC 44-5 |
| Spark Plug
Gap, Inch: .032 |
| Firing
Order: 12784563 (front
to rear: Left bank: 2-4-6-8; Right bank: 1-3-5-7) |
| Ignition
Timing: Yellow timing
mark aligns with "5" on timing indicator: Location:
Vib. Damper |
| Engine
Idle Speed, RPM:
450 |
| Cylinder
Head Torque Lbs.Ft.: 63-73 |
| Compression
Pressure & Cranking Speed: 150
Min. |
| Voltage & Polarity: 12
volts, negative ground |
PISTON AND RING SPECIFICATIONS
|
Fitting
Pistons with Scale:
Shim thickness .003
Pounds on Scale: 7 to 13 |
Ring End
Gap:
Compression: .010
Oil: .015 (no fitting required on Flex-Fit oil rings) |
| Clearance
in Groove: Compression:
.002-004; Oil: .0035-.0095 |
| Wristpin
Diameter, Inch: .940 |
VALVE SPECIFICATIONS
|
Operating
Clearance:
Intake: 0 Exhaust:
0 |
| Valve Seat
Angle, degrees: 45 |
Valve Timing: (BTDC
= before top dead center; ATDC = after top dead
center)
Intake
opens: 25 degrees BTDC
Exhaust
Closes: 42 ATDC |
Valve Spring
Pressure Pounds at Inches Length:
Inner
Spring: 53 @ 1.15; Outer Spring: 85 @ 1.12 |
| Valve Stem
Clearance: Intake: .0025; Exhaust:
.003 |
ENGINE BEARING SPECIFICATIONS
|
Connecting Rod Bearings:
Journal
Diameter, Inches: 2.249-2.250
Bearing Clearance, Inch: .0002-.0023
Rod End Play, Inch: .006-.011
Rod Bolt Tension: Lbs.Ft.: 45-55 |
Main Bearings:
Journal
Diameter, Inches: 2.498-2.499
Bearing clearance: .0005-.0025
Shaft End Play: .004-.008 (Thrust
on Bearing No. 3)
Main Bolt Tension: Lbs.Ft.: 100-110
|
CAPACITY DATA
|
Cooling
System:
Super
V8; Century V8:
Without
heater: 16-1/2 quarts (with Dynaflow 18)
With heater:
18; quarts (with Dynaflow
18)
Roadmaster V8:
Without heater:
18
With heater:
20 |
| Fuel Tank: 19
gallons |
| Engine
Oil: 6 quarts |
| Transmission: 2-1/2
w/auto 10 qts. |
| Rear Axle: 4-1/2
pints |
1954 Buick 322 (177 hp) V8 Engine Specs
1954 Buick 322 (182 hp) V8 Engine Specs
1954 Buick 322 (195 hp) V8 Engine Specs
1954 Buick 322 (200 hp) V8 Engine Specs
1954 Buick 322 V8 Engine Specs:
Delco-Remy Distributor Specs
1954 Buick 322 V8 Engine Specs:
Delco-Remy Generator Specs
1954 Buick 322 V8 Engine Specs:
Delco-Remy Regulator Specs
1954 Buick 322 V8 Engine Specs:
Delco-Remy Starting Motor Specs
1954 Buick 322
Wheel Alignment Specs
Return to Buick Engine Specs Index
|
